I then had further issues with my partitioned drive.Īfter using the options within the windows installer to access the command line and using disk part to erase the disk I still failed #Bootchamp tutorial windows 10 windows 10#I had some issue with bootcamp so I option booted from the windows 10 DVD (choosing efi boot) #Bootchamp tutorial windows 10 drivers#All drivers are working except the nvidia one ?. #Bootchamp tutorial windows 10 install#I install the bootcamp drivers 4, 5 and 6 in my old iMac 2009. It will not complain if your system is not allow to install them. Using "start \boocamp\Apple\bootcamp.msi". Pgleesonuk, it is better to use the Windows PowerConsole (c:\windows\system32\WindowsPowerConsole\) to install the bootcamp drivers. I couldn't find anyone who got the nvidia 9400M working on a iMac 2009 in Windows yet but regarding your problem I read some cases of users installing rEFInd ( ) and using it as a boot loader, load the specific PCI address for the components their iMacs have. As result, the system gets into a continuous reboot loop. By my side, it looks like the installed Windows EFI is not getting on well with my Nvidia 9400M and it doesn't matter which drivers I am installing (Windows Update, Bootcamp 4, 5 or 6 or the Nvidia proprietary), none of them is getting the correct PCI address. The hardware do not recognise the installed drivers which usually make a reference to a wrong hardware address (PCI address I think). Our systems are different (late 20) although the problem looks the same. #Bootchamp tutorial windows 10 driver#Once there, you can revert the wrong controller back to the previous driver (using the device manager) or just disable it. Thuber, I will recommend you to restart in Windows 10 safe mode using the installation disk/usb you used during the installation. It is always the same issue, the system starts, windows 10 loaded, black screen, reboot.ĭid you have the same problem? Have you identify the issue?.Ĭorrect, the main problem are the drivers installed by Windows Update. Because of it, I think the problem is related to a driver installed by Windows 10 updates sooner or later, not by the bootcamp drivers. I have repeated the process several times and it doesn't matter if I have installed the bootcamp drivers or not, at some point the system is not able to complete the booting and Windows 10 reboot again. After restart Windows 10, it is in a rebooting loop, it is not able to load the Windows 10 drivers until the end. Once in Windows 10, I have installed the bootcamp drivers and the installation was fine. Afterwards, I have installed Windows 10 properly. I have partitioned the disk using bootcamp, disable the System Integrity protection in recovery mode (because I am using El Capitan) so I can install Windows 10 in the bootcamp partition. iMac late 2009 21.5" with Windows 10 (EFI install disk) using bootcamp. Hopefully the bootcamp drivers will fix it.ĭoes anyone else have any tips or success stories to share? Next thing to try will be to install the bootcamp 5.1 drivers in safe-mode individually as the setup.exe complains about the version not being supported. On investigation this is something to do with networking, but I'm no expert in this matter. The last entries on this log are multiple attempts to load AFD.SYS Going into normal safe-mode works fine, and I selected the boot logging option. Then you get various options for safe mode, command prompt, network etc. You need to hold F8 down before you select the EFI-Boot with enter. I can take the USB stick out and safe-boot into the EFI-Boot option that now exists on the list of available boot disks. I get the spinning balls progress icon then black screen. I booted from the "EFI-Boot" USB stick and went through the install process. "Remove a hybrid MBR using gdisk: Use the experts' menu ("x"), then type "n" to create a new protective MBR, then "w" to save your changes." With some help from Rob Smith (rEFInd) I fixed this using gdisk to write a new Protected MBR Made sure I had a free partition on a standard GUID partitioned disk (my original hard disk), importantly without a previous install of bootcamp as this creates a Hybrid MBR which Windows 10 refuses to install on too. I have a working Windows 7 bootcamp partition, that until I can prove Windows 10 works, I don't really want to delete/upgrade.ĭownloaded the media creation tool ( ) to make a USB stick #Bootchamp tutorial windows 10 upgrade#I'm on a quest to run Windows 10 on my late 2009 27" iMac.Īfter my recent upgrade to an 1TB SSD and 16GB ram it's still a great computer.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |